UTP Cat6 Cables price in Pakistan

UTP Cat6 Cables price in Pakistan

The UTP Cat6 cable price in Pakistan varies depending on the brand, quality, and material (pure copper vs. copper-clad aluminum). On average:

Litech Pakistan offers competitive prices on high-quality, pure copper Cat6 cables to ensure the best performance for your network needs.

Cat6 Cable FAQs

What is Cat 6 Cable?

Cat 6 (Category 6) is a cabling standard used primarily in Ethernet computer networks, security systems, and telephone services.

Compliant with Category 5E, Category 6 (Wiki) cable is capable of transmitting voice and data at speeds of up to 155 Mbps, with transmission frequencies of up to 550 MHz possible.

Does Cat6 support Gigabit?

Cat 6 supports 10Base-T, 100Base-TX, and 1000Base-T (Gigabit Ethernet) Ethernet connections.

Category 6 cable has more stringent requirements for interference and system noise than previous cable standards.

How many pairs of Cat6?

Category 6 cables have four pairs of twisted copper wires, with each twisted pair made of 23 mm thick copper.

The previous Category 5 model used 24 mm thick copper wire. In the case of wire gauges, the higher the number, the smaller the wire.

Can I use RJ45 for Cat6?

Cat 6 cables are usually terminated with RJ-45 electrical connectors.

If components from different cable standards are mixed, the signal path performance will be limited to the lowest category.

What is the maximum length allowed for a permanent Category 6 link?

The maximum length of a Category 6 cable segment is 220 meters.

To transmit data over long distances, it is necessary to install a repeater, otherwise data loss can occur.

How to make a Cat6 patch cable?

Cat 6 cable is more difficult to install than Cat 5 or Category 5E. The main reason is that the conductors in Category 6 cables are twisted more tightly.

Which makes them more difficult to separate. Apart from that, everything else is basically the same as installing Cat 5 or Cat 5E cables.

Cable manufacturers offer connectors and panels with much sharper teeth that help separate the wires into pairs and easily terminate the Category 6 cables.

However, it is recommended that you take a little extra time to install Cat 6 cables and do it properly without cutting your fingers.

Step 1:

This method is usually used for Cat 6 RJ45 connectors.

An alternative method is available for connectors that use a “bar-bar”.

Step 2:

Cut the cable to the desired length.

If you are going to use bare-metal covers, now is the time to install them.

Make sure the covers are “out” toward the connector.

Step 3:

Strip off about 1 inch of the cable jacket.

Use a crimp cutter or wire stripper by hand.

Be careful not to cut any individual wires.

Twist each of the 4 pairs and flatten each wire between your fingers as much as possible. Step 4

Use the 568-B wiring diagram on both ends of the standard jumper cable.

Step 5:

Place all wires as close together as possible.

Hold the grouped (and sorted) wires firmly between your thumb and forefinger.

Cut all wires at 90 degrees from the wire,

1/2 inch from the end of the wire jacket.

Use a sharp cutting tool to prevent the wire ends from “smashing.”

Step 6:

With the connector pins facing up, carefully insert the wires into the connector.

Apply moderate pressure to properly press the wires into the connector pins.

Alternative to Load Bar Connectors

A.

Note that the load bar has grooves on one side with a flanged edge on one side.

The slotted side should face the pins inside the connector.

The wires will be inserted into the flanged end.

Hold the grouped (and sorted) wires firmly between your thumb and forefinger.

Cut all wires at a sharp angle away from the cable.

Use a sharp cutting tool to prevent the wire ends from “breaking.”

B.

Hold the load bar so that the through holes are facing the cable.

Insert the wires one at a time through the load bar, carefully observing the direction.

Pull the load bar as far as it will go.

D.

Cut off the excess wire ends with a straight cut about 0.25 inches from the load bar.

With the connector pins facing up, insert the load bar assembly into the connector.

Make sure the wires are packed tightly into the end of the connector.

The brown pair of wires should be on the right side.

Step 7:

Look at the tip of the connector to make sure all the wires are fully inserted.

The end of each wire should be visible.

There should be enough cable jacket in the center of the connector to fill it.

Note: To ensure perfect alignment, move the weight bar forward if necessary.

Step 8:

Place the connector in the crimping tool and press firmly until the handle reaches a full rotation.

Step 9:

Repeat the process on the other end, using the correct wiring diagram.

Once you’re done, make sure to firmly replace the protective covers on the connectors.

Step 10:

Always use a cable tester to check for continuity, opens, and shorts.

Step 11:

Making patch cables takes practice, so don’t stop until you’ve mastered the technique.

pure copper cat6 cable black copper cat6 cable price in pakistan cat6 copper cable cat6 copper cable price cat6 copper cable price in pakistan cat6 pure copper cable cat6 cable price in pakistan per meter